fortypoundhead.com

Misuse of Network Time Server Systems

Posted On 2007-06-18 by FortyPoundHead
Keywords:
Tags: Security 
Views: 1541


Network Time Protocol (NTP) is a standard Internet protocol for the dissemination of time around a computer network. The protocol operates in a hierarchical manner, each level or stratum serving the next level in the hierarchy. At the top of the hierarchical structure is a stratum 1 NTP server that synchronises to an external time and frequency reference. Many stratum 1 NTP servers reside on the Internet and are used for synchronising network time clients.

Over the last few years, there have been a number of NTP server abuse and misuse reports. This article discusses some of the reported NTP time server abuse incidents and describes NTP configuration methods that can reduce such problems. Many reported incidents seem to be because of equipment manufacturer configuration errors rather than malice.

Many NTP server misuse issues have arisen from client configuration errors, particularly in consumer electronic equipment. Due to the volume of consumer electronic equipment manufactured and in-use, any configuration issues with equipment that access NTP time servers can greatly magnify problems. Typically, clients with configuration errors or firmware bugs that cause repeated access to a network time server can cause server loading problems when a large number of clients are involved.

A recent high-profile incident of consumer electronic equipment causing NTP server problems was with consumer router equipment. Home router devices were accessing stratum 1 Internet time servers and flooding them with requests for time. Many NTP time server administrators noticed a large increase in traffic and server loading. Many stratum 1 NTP servers have an access policy that forbids anything other than a stratum 2 server from requesting time. Home router equipment should not therefore directly access a stratum 1 time server.

In a separately reported network time server misuse case, an Internet based NTP server was being bombarded by ever-increasing volumes of traffic. It was initially thought that this was due to an attack on the server. However, the amount of traffic continued to rise over time rather than decrease. It was eventually found that home router equipment manufactured by a large manufacturer had hard coded the NTP servers IP address in the products firmware. Each router in operation was contacting the server at regular intervals in an attempt to synchronise time. The volume of devices in operation eventually overloaded the server.

The NTP protocol implements a rather general-purpose address mask restricted use policy. This allows only IP addresses within a specified range or that fit a specified address mask access to a NTP time server. Alternatively, clients can be excluded from access by explicitly including them in a restriction list. Rogue clients can therefore be excluded access to the NTP server by explicitly restricting access.

Usually, the server drops NTP requests that are denied access. However, occasionally a harsher response is required. The server can respond with a message explicitly requesting the client to cease sending. A ''kiss-o-death'' packet has been created especially for this purpose. Kiss of death (kod) codes can provide an intelligent time client with useful synchronisation information. The packet contains character strings, that can be easily read in log files, that explain the denial of service. When a client receives a ‘kiss-o-death'' packet, it should stop sending to a particular server and locate an alternative server, if available. If an altenative is unavailable, the time client should only re-contact the time server after an exponentially increasing time.


About the Author

FortyPoundHead has posted a total of 1974 articles.

 


Comments On This Post

No comments on this post yet!


Do you have a thought relating to this post? You can post your comment here. If you have an unrelated question, you can use the Q&A section to ask it.

Or you can drop a note to the administrators if you're not sure where you should post.


Your IP address is:54.158.195.221

Before you can post, you need to prove you are human. If you log in, this test goes away.



Recent Forum Posts

Malicious IP Checker Companion Tool
dwirch posted on August 12, 2017 at about 20:24 in Site News

Job Spammer: Steve Adams
dwirch posted on August 8, 2017 at about 7:44 in Spammers

New security implemented
dwirch posted on August 8, 2017 at about 6:43 in Site News

New security implemented
dwirch posted on July 23, 2017 at about 6:58 in Site News

Fold Code Manager into main KB?
VB6Boy posted on July 22, 2017 at about 14:42 in Site News

Fold Code Manager into main KB?
dwirch posted on July 22, 2017 at about 14:41 in Site News